YOUR PLUMBING CRASH COURSE: A GUIDE TO INSTALLING A BATHTUB

Your Plumbing Crash Course: A Guide to Installing a Bathtub

Your Plumbing Crash Course: A Guide to Installing a Bathtub

Blog Article

Additional Information

Do you find yourself interested in info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?


How to Install a Bathtub Yourself
Mounting a bathtub isn't exactly rocket science, yet it does require solid plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old tub with a new one is additionally a moderately challenging job. If the old tub is readily available, the project can move easily; if you need to open a wall to get rid of the old bathtub as well as position the brand-new bath tub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will need a helper to leave the old tub as well as embeded in the new one. Make sure you have qualified yourself for the task and are comfortable trying it. Rather than employing a service provider to take over a halfway-completed task, it is much better to think about using one before you start. Chances are you may need a specialist plumber to make tube links.
This post will assist you install a new bathtub in your restroom if you have actually already acquired a brand-new bathtub and also don't need to change the setup of your previous water system pipelines.
Your tools as well as material list should make up the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you need to change old taps with new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, turn on the taps to drain any type of water continuing to be in the system. The process of getting rid of the existing faucets can be rather troublesome due to the limited access that is often the situation.
    Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a towel prepared for the remaining water that will originate from the pipes. Once the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from turning throughout this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old securing substance.
    Before proceeding to fit the brand-new faucets, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.

    Suitable New Touches


    If the tails of the new faucets are plastic, after that you will need a plastic port to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end gives a connection to the existing supply pipes.
    If you need to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
    Next off, place the tap in the placing opening in the bath/basin making certain that the washers are in area between the faucet and the sink. Protect the faucet in place with the maker supplied backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular tap ports. The previous kind should be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been connected.

    Setting up the Tub


    Using both wood boards under its feet, position the tub in the needed setting. The wood boards are handy in uniformly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto four tiny points.
    The next objective is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bathtub until the level reads degree.
    To mount taps, fit the bottom of the furthest versatile faucet connector to the appropriate supply pipeline by making a compression join; after that do the same for the other faucet.
    Activate the water and also check all joints and also brand-new pipework for leakages as well as tighten them if essential. Fill up the bath tub as well as likewise examine the overflow electrical outlet and also the typical outlet for leakages.
    Lastly, fix the bathroom paneling as explained in the producer's user's manual. Tiling and also securing around the tub needs to wait till the bath tub has been used at the very least once as this will resolve it right into its last position.

    Preparing for the Installment


    First of all, the supporting frame supplied with the bath ought to be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to ensure that if the tap features a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets device to stop strain on the bath tub.
    Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
    Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last setting.

    Tiling Around the Tub


    In the area where the bath fulfills the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack a rigid seal, creating the water to permeate the wall surface in between the bath as well as the tiling, leading to difficulties with wetness as well as feasible leaks to the ceiling below.
    You can pick from a selection of coloured sealants to blend in your fixtures and fittings. They are marketed in tubes and cartridges, and can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to securing, to allow for the motion experienced when the bathtub is in usage. The sealant can fracture relatively very early if you do not think about this motion before sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise quickly offered on the market. It is recommended to fit the ceramic tiles making use of waterproof or waterproof sticky and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    We had been made aware of that editorial on Installing A Bathtub through an associate on our other website. Sharing is caring. You won't know, you could be doing someone a favor. We love reading our article about Installing A Bathtub.


    Book Inspection

    Report this page